Signal Routing / Switching : Expanders : ClearOne - CONVERGE Pro 2 USB Expander

Professional Converge USB Digital Audio Expander

Model: CONVERGE Pro 2 USB Expander

Part #: 910-3200-302

USB Audio
2 x 2 channels - Tx X Rx, with left and right channels
Professional quality digital audio - 48kHz, 24-bit
USB 3.0 and USB 2.0 ports compatible
Windows/Mac compatible

More Product Information Below

Compare

Project List

Product Info

Tech Specs

Documents

The USB Expander expands the USB Audio capability of a CONVERGE Pro 2 mixer by providing an additional USB audio interface with 2x2 channels.

This device enables users in different rooms to run UC applications in laptops for a professional quality audio experience using a simple, flexible USB connection.

The USB expander can be daisy-chained with other P-Link peripheral devices such as the Beamforming Mic Array 2, DIALOG 20 Receiver, and GPIO Expander. It can be used as a P-Link distance extender.

USB Audio
2 x 2 channels - Tx X Rx, with left and right channels
Professional quality digital audio - 48kHz, 24-bit
USB 3.0 and USB 2.0 ports compatible
Windows/Mac compatible
Daisy-chainable
Maximum 3 USB expanders per CP2 device
Daisy-chains and co-exists with other P-Link devices
Extends distance
By 200 feet (60 meters) from CP2 device
By 200 feet (60 meters) for other P-Link devices
Form factor and mounting
Compact form factor - 1/3rd RU width, 1U height
Rack-shelf mount
Under the table mount
Wall mount
Ceiling mount
Connectivity and power
Direct connection to CONVERGE Pro 2 (CP2), Beamforming Microphone Array 2, and DIALOG 20 Wireless Receiver
P-Link for power, audio, control from CP2
PoE Injector for power
RS-232 connection for control interface
USB connection for audio
Applications:
Unified communication (UC)
Video conferencing (VC)
Audio playback
Audio recording

Rackmountable - Yes
Spec Sheet available - Yes

Operating Temperature (Maximum): 104 F
Operating Temperature (Minimum): 14 F
Number of Channels: 2
Number of Inputs: 2
Number of Outputs: 2
Rack Units (Height): 1
AC Voltage (Maximum): 240 Volts
AC Voltage (Minimum): 100 Volts
Active Power: 3 Watt
Depth: 1.60 in
Height: 4.10 in
Width: 5.50 in
Product Weight: 0.88 lbs
USB Audio:
•Port Type: USB-B connector
•Audio: Digital audio, 2 x 2 bidirectional channels
•Sample Rate: 48kHz
•Sample Bit Depth: 24Bit
•Compatible: USB 2.0, USB 3.0
•USB Cable Distance: 16 feet (5 meters)
•Compatible: Windows and Mac OS devices
P-Link Peripheral Bus:
•Ports Type: RJ-45 (Cat5e or Cat6)
•P-Link In and Out: proprietary peripheral bus
•PoE In:
•P-Link In Port
•PoE IEEE802.3AF
•Audio:
•Up to 3 USB Expander units + Beamforming Microphone Array 2 units + up to 3 DIALOG 20 Wireless Receiver units
•Cable: Solid core 24AWG, factory terminated Cat 5e or Cat 6 cable
•Distance: Up to 200 feet (60 meters)
•Daisy-chain:
•Up to 3 USB Expanders with each CONVERGE Pro 2 unit
•Up to 3 Beamforming Microphone Array 2 units and up to 3 DIALOG 20 wireless
•Receiver units along with up to 3 USB expander units with each supported CONVERGE Pro 2 unit in the same chain
•Up to 6 USB Expander units in the same chain with 2 supported CONVERGE Pro 2 units connected through C-Link
RS232:
•Type: 3 Position (Tx, Rx, Gnd) 3.81mm Grey Header, Male, Phoenix type Euro block connectors
•Support: Serial commands
•Connection: Connect with Touch Panel Controller for CP2, third-party control devices
Power Selection Switch:
•Sensor Type: Slide Switch
•Toggle toward P-Link to power device by P-Link
•Toggle toward PoE to power device by PoE Injector
PoE In Port:
•Port Type: RJ-45 port
•PoE: 802.3af or 802.3at PoE/PoE+ injector input
Configuration and Administration Software:
•CONVERGE Pro 2 CONSOLE software
Front Panel LEDs:
•Power LED:
•Off: Not powered
•Solid Blue: Powered ON
•Status LED:
•Off: No P-Link plugged in
•Solid Blue: P-Link plugged in and system working normally
•Flashing Blue: Locate mode initiated from CP2 CONSOLE Software
•Red: Error condition
Mounting:
•Rack-shelf mount
•Underneath table mount
•Wall mount
•Ceiling mount
Power and Thermal:
•Power Type: PoE/PoE+
•Port Type: RJ-45
•Power Source: P-Link or PoE Injector
•PoE In/P-Link In: 802.3af or 802.3at PoE/PoE+
•Power Source Indicator: Set the position of the Power Select switch to indicate the source of the power (P-Link or PoE)
•Typical Thermal: 10.24 BTU/Hr Max
Dimension and Weight:
•With rack-ears Width x Depth x Height: 6.8x1.7x 4.1-inch or 17.2x4.3x10.3cm
Parts Included:
•Rack Mounting Ears: Pre-installed, Qty 2
•Input Connectors:
•3.81mm Terminal Block Connector, 3 Position (Grey), Qty 1
•USB Cable: USB Type A to Type B, 6 Ft (1.8M), Qty 1

USB Expander 766911 kb - Data Sheet

Project List

Suggested Products

TesiraCONNECT TC-5 - 5-port Expansion Device

by Biamp

18Gbps HDMI Extender

by Alfatron Electronics, Inc.

Tesira EX-UBT Expander

by Biamp